Skip to main content

Filter By:

  • Show More Sizes
  • Show Fewer Sizes

Tools & Tuning

$36.00
Protects the wax base during transport and is easy to prepare for the next training session. A versatile hard glide wax. Used by Racing Service and ski factories as a transport wax and as an effective preparation for the next summer snow training session. - Easy to apply with a waxing iron. - Easy to scrape and brush. - Fluoro-free
$9.00
F4-100NC has a sponge foam applicator on one side of the bottle for applying wax, and a felt pad on the other side for polishing. A handy bottle to carry in your pocket. Apply a thin layer over the base surface. Let it dry for approx. 2 minutes. Finish by polishing with the felt pad. Apply F4 to the steel edges when storing your skis or board after the season. This prevents the edges rusting.
$9.00
F4-100NW has a sponge foam applicator on one side of the bottle for applying wax, and a felt pad on the other side for polishing. A handy bottle to carry in your pocket. Apply a thin layer over the base surface. Let it dry for approx. 2 minutes. Finish by polishing with the felt pad. Apply F4 to the steel edges when storing your skis or board after the season. This prevents the edges rusting.
$15.00
F4 spray universal glide wax for skis and snowboards. A wax with a wide range of uses. - Universal wax for all temperature ranges - Easy application - Glide wax for ski mountaineering and summer skiing
$48.00 - $100.00
HS10 is a great base prep wax, but also a great training wax. Ideal in warm conditions, typically during spring skiing. For racing, we recommend going with a top coat as the final layer. The speed of the iron should be approx. 8-10 sec. on a skating or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. It's important to have a good iron to get an efficient melting of the wax. Recommended iron temp: 150°C (302°F). Details: - A popular wax in nordic disciplines - Good water repellent properties - Replaces LF10X - For training and competition Highlights: - For warm conditions - Easy to work with - For training and competition - Great performance and durability - Fluoro-free and non-toxic - Well tested on many conditions
$48.00 - $300.00
The 5 series is the hardest wax in the HS line, and is a great choice in cold conditions, due to its great durability and dry friction properties. It’s a great choice both for alpine and cross country. Despite being a wax for cold conditions, the melting point makes it easier to apply than many competitors in this area, without sacrificing the great glide properties. For fresh, old, or manmade snow. - HS5 can be used as a race wax alone or as a base for top coats. - Recommended iron temp: 150°C (311°F). - -10°C to -18°C (14°F to 0°F).
$48.00 - $300.00
HS6 is very versatile. Its area of use stretches from underlayer for powder to racing wax and base prep wax for cold skis. HS6 has good durability and offers great performance on natural and artificial snow. The speed of the iron should be approx. 8-10 sec. on a skating or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Important to have a good iron to get an efficient melting of the wax. HS6 can be used as a race wax alone or as a base for top coats. Recommended iron temp: 155°C (311°F). Highlights: - Fantastic allround glider - For training and competition - Great performance and durability - Fluoro-free and non-toxic - Exists also in liquid - Well tested on many conditions
$48.00 - $300.00
HS7 performs great in normal winter conditions below the freezing point. Its hardness makes it convenient to work with and easy to get a good end-result. Can be used as a racing wax at low air humidity, but will also serve the purpose as a brilliant training wax. The speed of the iron should be approx. 8-10 sec. on a skating ski or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Important to have a good iron to get an efficient melting of the wax. HS7 can be used as a race wax alone or as a base for top coats. Recommended iron temp: 150°C (302°F). Highlights: - Fantastic allround-glider - For training and competition - Great performance and durability - Fluoro-free and non-toxic - Well tested on many conditions
$48.00 - $300.00
A great wax for both base-prep and training. It can also be used as a race wax, preferably used with a top coat. Easy to melt and very convenient to work with. The speed of the iron should be approx. 8-10 sec. on a skating or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Important to have a good iron to get an efficient melting of the wax. Recommended iron temp: 150°C (302°F). Replaces the LF8X. Highlights: - Easy to work with - For training and competition - Great performance and durability - Fluoro-free and non-toxic - Well tested on many conditions
$18.00 - $40.00
A wax for extreme cold conditions, which can perfectly be used alone as a race wax when the air humidity is low. It performs very well on artificial snow and has great durability. The speed of the iron should be approx. 8-10 sec. on a skating or alpine ski. The wax can be re-heated after cooling to room temperature (10 min.) for better durability. Scraping after approx. one minute. It’s important to have a good iron to get an efficient melting of the wax. Scraping after approx. one minute. In the warmer part of the temperature range, and when high air humidity, a powder or other top coat product will increase the performance. - Recommended iron temp: 155°C (311°F). - Replaces the CHX4. - -14°C/-32°C (7°F to -26°F).
$18.00 - $120.00
PS10 is an economic training and racing wax as well as base prep wax for warm skis. Easy to melt and very convenient to work with. The speed of the iron should be approx. 8-10 sec. on a skating or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. It's important to have a good iron to get an efficient melting of the wax. Recommended iron temp: 120°C (248°F). - A versatile wax for warm conditions - Low melting point and easy to apply
$18.00 - $120.00
The PS5 is the hardest wax in the line, and is a great choice in cold conditions, due to its great durability and dry friction properties. It's a great choice both for alpine and cross country. Despite being a wax for cold conditions, the melting point makes it easier to apply than many competitors in this area, without sacrificing the great glide properties. For fresh, old, or manmade snow. The speed of the iron should be approx. 8-10 sec. on a skating ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Scraping after appr. one minute. Important to have a good iron to get an efficient melting of the wax. PS5 can be used as a race wax alone or as a base for top coats. Recommended iron temp: 150°C (311°F) - Recommended iron temp: 150°C (311°F). - Replaces the CH5X. - -10°C to -18°C (14°F to 0°F).
$18.00 - $140.00
PS6 is very versatile. Its area of use stretches from underlayer for powder to racing wax and base prep wax for cold skis. PS6 has good durability and offers great performance on natural and artificial snow. The speed of the iron should be approx. 8-10 sec. on a skating or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Important to have a good iron to get an efficient melting of the wax. PS6 can be used as a race wax alone or as a base for powders and other top coats. Recommended iron temp: 145°C (293°F). - Recommended iron temp: 145°C (293°F). - Replaces the CH6X - -6°C to -12°C (21°F to 10°F).
$18.00 - $140.00
PS7 is a wax that performs great in normal winter conditions below the freezing point. Its hardness makes it convenient to work with and easy to get a good end result. PS7 is an economic training and racing wax as well as an all-round base prep wax. The speed of the iron should be approx. 8-10 sec. on a skating or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. It's important to have a good iron to get an efficient melting of the wax. Recommended iron temp: 140°C (284°F). - Recommended iron temp: 140°C (284°F). - Replaces the CH7X. - -2°C to -8°C (28°F to 18°F).
$18.00 - $120.00
PS8 is an economic training and racing wax as well as base prep wax for warm skis. Easy to melt and very convenient to work with. The speed of the iron should be approx. 8-10 sec. on a skating or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. It's important to have a good iron to get an efficient melting of the wax. Recommended iron temp: 130°C (266°F). - Recommended iron temp: 130°C (266°F). - Replaces the CH8X. - -4°C to +4°C (25°F to 39°F).
$40.00
Wall thermometer with waxing tips. - Wall thermometer - For your house or cabin wall - For all skiing enthusiasts - Practical waxing guide
$65.00
Steel brush. Ø 0.18 mm. Used as first brush on wax after scraping. 5-6 strokes. High quality steel brush that has had an excellent reception in racing.
$27.00
Cleans integrated skins in a gentle way without affecting the skin glue. Restores the properties of the skin and increases its efficiency. To be used after skiing. - Can also be used for backcountry skiing - Easy to use - Apply after skiing - Must have when using skin skis - Fluoro free ski wax - Swix ski wax
$19.99
Swix skin wax for backcountry and alpine touring. - To be applied on skins. - For all snow conditions. - Aerosol with applicator.
$12.00
Steel scraper for experienced waxers. Sharp steel scraper for peeling or straightening bases.
$140.00
Lightweight and tailor-made for SWIX tables! Cross Country profile in plastic, To use with our wax tables, For all skiers, Lightweight and stable. Thermo plastic profile for cross country skis. Fits into waxing tables T0076, T0076-2, T00754, T0075W. Same profile both in the front and back. Includes holder for fixing the binding. Suitable for both classic and skating skis in lengths from 170-210 cm. Lightweight and very stable to work with. Weight: 1.4 kg/3.2 lbs.
$8.00
Synthetic cork for kick wax. This synthetic cork has a higher density than a regular synthetic cork. For racing.
$29.00
All-round brush. It will polish the liquid/pastewaxes and will also work on the harder melt on waxes. Has both bronze and nylon brittles for all waxes. Blister pack w/alarm label - Bronze and nylon brush - Swix waxing brush - Solid hand brush - High quality - Must have for ski waxers
$19.95
Practical all-round brush with pocket-sized nylon bristles. Top quality. - Nylon brush - For polishing glide wax - For those who want a better skiing experience - Ergonomically designed
$30.00
Medium bronze brush. Ø 0.15 mm. First brush used after scraping. For brushing glide wax out of the structure. 10 strokes. Blister pack w/alarm label. Features: - Bronze brush - Swix waxing brush - Solid hand brush - High quality - Must have for ski waxers
$22.00
The ideal brush when applying any F4 product. White felt for spreading the F4 product evenly on the base and for polishing. The nylon for brushing and removing excess wax from the structure. This process will increase the durability of any F4 product. Good quality. - For training and competitions - Fluorine free and 100% biodegradable - Thoroughly tested on several types of conditions
$8.99
Transparent polyethylene sticks for repairing ski bases. Easy to work with. Ø 6 mm. 4 sticks per pack. First clean the damaged area in the base and scrape out any loose residue. Heat the polystick and drip into the damaged area in the base. Let it cool down and scrape away the excess with a steel scraper, or panzer file if necessary, and polish over with Fibertex for a fine finish. - Polyethylene Stick - For repairing ski bases - For racing service and ski workshops - Easy to work with
$6.99
Transparent polyethylene sticks for repairing ski bases. Easy to work with. Ø 6 mm. 4 sticks per pack. First clean the damaged area in the base and scrape out any loose residue. Heat the polystick and drip into the damaged area in the base. Let it cool down and scrape away the excess with a steel scraper, or panzer file if necessary, and polish over with Fibertex for a fine finish. - Polyethylene Stick - For repairing ski bases - For racing service and ski workshops - Easy to work with
$29.95
Structure steel insert for SWIX Super Riller. Fine 0.5 mm. - Structure steel insert - For Swix Super Riller structure tool - For cross-country skiers - High steel grade
$25.00
Sharpener for plexi scrapers with short, sharp file, 40 mm. Can be mounted on a wall or waxing table. It is important to use sharp scrapers when prepping. Sharp scrapers enable you to remove wax more easily and efficiently. The file can be flipped over and used on both sides for longer durability. - Sharpening tools - For plexi scrapers - For all ski waxers - Sharp file
Page 1 of 2 Next page
Reviews_by_listen360_large